Damp Proofing Cream sold as a 6 x 1 litre pack for the treatment of damp walls. Using a large caulking gun to inject the cream into the wall the cream will provide an effective barrier against rising damp in walls.

Extra large heavy duty DPC injectiongun for rising damp treatment using Ultracure chemical damp proofing cream supplied in 1000ml cartridges

Ultracure DPC cream in 380ml cartridges. Treat damp walls with advanced chemical damp proof course products. No specialist equipment needed. Simple DPC injection treatment using caulking gun.

Ultracure DPC cream in 1ltr cartridges. For the treatment of rising damp in both solid and cavity walls. No specialist equipment needed. Simple DPC injection treatment using a 1ltr caulking gun.

Ultracure Damp Proof Injection cream in a 3 litre tubl for the treatment of damp walls. Advanced chemical damp course injection applied via a low pressure pump and nozzle. This tub treats up to 15m of double leaf wall.

Hydraflex is a two component flexible coating , it can be applied to mineral substrates such as Concrete and Masonry to provide a waterproof barrier.

Grade 1 commercially pure titanium wire for use in Lectros osmotic DPC systems.

A pack of 25 platinum coated titanium anodes connected to pure titanium wire for use in Lectros osmosis DPC systems.

Standard Lectros power control unit for electro osmotic damp proofing.

A copper plated cathodic ground rod for attracting free moisture molecules in electro-osmotic damp proof sytems

Commercially pure titanium crimps for connecting titanium wires when using an electro osmosis system for damp proofing stone walls with rubble fill. Pack quantity 10.

ISO-THERM is an ultra thin specially woven polyester based thermal wall insulation , it is flexible and lightweight and will accommodate a plaster skim finish.

Heat recovery fans control humidity levels and reduce the likelihood of condensation. This heat exchange ventilation unit provides a continuous air change with minimum heat loss

Fixings for securing insulated plasterboard sheets to brick and block walls. Fire proof fasteners with galvanized coating for internal solid wall insulation in packs of 20 or boxes of 400

Heat recovery units in a multi-buy pack of 4. These humidity control heat exchange fans reduce relative humidity and alleviate condensation, providing continuous ventilation with minimum heat loss.

A waterproof fibre faced sealing tape for butt joining mesh-faced damp proofing membrane. The fibre tape takes traditional renders and dot and dab adhesives. 25m x 115mm

A lightweight renovating plaster pre-mix with perlite, fibres & water repellent additives. For use following damp proof treatments or in conjunction with cementitious tanking coatings. 20KG

Water-guard drainage channels drains groundwater from basements. Each 2 m long conduit has perforated sides and an upstand. Available in single pieces or a box of 8 pieces.

Hammer-in fixing with waterproof seal for use with air gap mesh membranes. Roughened head provides a key for plaster finishes. Bag quantity: 200

Mesh-faced membrane with 3mm studs and a polypropylene mesh to provide a key for plaster, render or plasterboard dry lining on plaster dabs. Roll sizes: 10m2, 20m2 and 40m2

CM8-Mesh Membrane withf 8mm studs and polypropylene mesh key for direct application of plaster, render or adhesive dabs for plasterboard dry lining. Rolls sizes: 20m2 and 40m2

CM8 is a versatile 8mm high tanking membrane for use in waterproofing damp proofing applications above and below ground level. Options: Rolls of 40m2 and 48m2

Waterproofing membrane kit with everything needed for waterproofing. Sizings 2 x 20m or 2 x 2.4m of floor or wall. Fix studs to basement membrane plugs for dry-lining walls. Lay screed direct.

Mesh membrane kit in 3 sizes with everything needed for waterproofing wall surfaces. These waterproof tanking membranes include a mesh face for direct application of plaster or dabs for plasterboard. 2.20m or 2.10m sizings